PIAB RTM Rope Tension Meter
RTM
The PIAB RTM Rope Tension Meter is very simple and handy to
use. Simply hold and “clip” it to the rope to be tested and use the large hand
screw to deflect the rope to a fixed angle. The resultant force will affect the
load cell and measure the tension in the wire rope. The resultant signal is
digitally processed and displayed in a selected pre programmed graduation. The
PIAB RTM 20D can be graduated in kN, klbs or in ton.
RTM
Измеритель натяжения тросов PIAB RTM прост и удобен в обращении. Для
проверки просто закрепите его на тросе и используя винт-зажим натяните трос до
фиксированного угла. Замер натяжения будет производиться вследствие давления
результирующий силы на датчик нагрузки. Сигнал будет обработан и отображен в
выбранных единицах измерения. PIAB RTM 20D может быть настроен в кН, klbs или тонах.
PIAB RTM range of
application
The PIAB RTM 20D was designed to swiftly and
accurately measure the tension in fixed or stationary ropes or cables i.e. guy
wires for masts and towers or other guyed constructions. The PIAB RTM 20D will
also be very useful in determining the tension in overhead suspension ropes for
railway catenaries.
The PIAB RTM 20D can be used to measure
tension forces up to 20 ton metric and for wire ropes with a diameter of up to
38 mm. Thanks to the use of microprocessor technology the PIAB RTM 20D can be
calibrated for up to 10 different wire rope dimensions/types. The digital read
out display will clearly show the tension of the wire rope selected. No
calibration tables are required. When calibrated for a specific rope, an
accuracy of 0,5-2% of rated capacity is normally obtained.
PIAB RTM safety
The PIAB RTM 20D is a delicate testing
instrument for swift, handy and accurate testing of pre tensioned stationary
ropes. Thanks to the design of the instrument it can temporarily be overloaded
up to 100% of its nominal capacity without affecting the accuracy of the
instrument. Thanks to tempered outer rope supports and a centre clamping jaw
the instrument gives a long service life with accurate measurements. The RTM
20D is delivered in a robust and light weight transport case (760 x 400 x 170
mm) for easy handling and protection of instrument.
Facts:
Control unit
Microprocessor.
Microprocessor.
Calibration
PIAB RTM 20 D can be calibrated for up to 10 different ropes. Load monitoring with RTM 20D does not interfere with the installation.
PIAB RTM 20 D can be calibrated for up to 10 different ropes. Load monitoring with RTM 20D does not interfere with the installation.
Accuracy
2-6% of max. rated capacity, depending on rope design.
2-6% of max. rated capacity, depending on rope design.
Temperature
range
-20 C to +70 C. (Standard electronics for load monitoring instruments tolerate only temperatures down to 0 degrees centigrade).
-20 C to +70 C. (Standard electronics for load monitoring instruments tolerate only temperatures down to 0 degrees centigrade).
Overload
accuaracy
The RTM 20D will temporarily withstand 100% overload without impairing accuracy.
The RTM 20D will temporarily withstand 100% overload without impairing accuracy.
Protection class
Pressure tight, conforms to IP 67 according to IEC 529
Pressure tight, conforms to IP 67 according to IEC 529
Weight
6.2 kg. Shoulder strap for onsite mobility and a fitted plywood case for transportation.
6.2 kg. Shoulder strap for onsite mobility and a fitted plywood case for transportation.
Tempered jaws minimise
wear and maintain accuracy.